Interactive IEEE Paper Walkthrough • Based on IEEE Access (2023)

Modeling and Designing of an
All-Digital Resonate-and-Fire Neuron Circuit

Trung-Khanh Le • Trong-Tu Bui • Duc-Hung Le
Faculty of Electronics and Telecommunications
University of Science · Vietnam National University, Ho Chi Minh City, Vietnam
DOI: 10.1109/ACCESS.2023.3287994 ↗
Corresponding author · ldhung@hcmus.edu.vn
Adapted for web by Aditya Bhatnagar
Electronics & Communication Engineering
University School of Automation and Robotics
New Delhi, India
threshold rest 1 · first pulse 2 · subthreshold oscillation 3 · second pulse (sums) 4 · threshold crossing 5 · SPIKE 6 · after-hyperpolarization
Abstract. Integrate‑and‑fire (IAF) and leaky integrate‑and‑fire (LIF) models are the popular models for spiking neurons and spiking neuron networks (SNN). They lack the dynamic properties of ordinary differential equation (ODE) models but are simpler; more than half of all digital neuron implementations use IAF or LIF. The resonate‑and‑fire (RAF) model proposed by Izhikevich keeps that simplicity while adding real dynamic behavior, but it has lacked a general hardware structure — most realizations have been analog. This paper develops and simulates the RAF equations with digital pulses, proposes block models of digital and all‑digital RAF neurons, and verifies the design on an Intel 28 nm Cyclone V FPGA. The resulting register‑transfer‑level (RTL) design uses just 23 D flip‑flops, with no floating‑point operations and no multipliers.
Index Terms — integrate‑and‑fire, leaky integrate‑and‑fire, resonate‑and‑fire, dynamic, all‑digital, FPGA
Section I

Introduction

Integrate‑and‑fire (IAF) and leaky integrate‑and‑fire (LIF) neuron models have appeared in thousands of studies. Although they are more than a century old, their simplicity has made them the default choice for simulating and building neuromorphic hardware.

The most biophysically complete model is the conductance‑based Hodgkin‑Huxley model (1952). Between 1960 and 2003, researchers proposed reduced alternatives — FitzHugh‑Nagumo (1961/1962), Morris‑Lecar (1981), Hindmarsh‑Rose (1984), and Izhikevich (2003) — each trying to keep some of Hodgkin‑Huxley's realism while cutting its computational cost.

The authors surveyed over 100 papers from 2000–2022 that turned spiking‑neuron models into integrated circuits or FPGA emulations, grouped by model: IAF (27 papers), LIF (37), FitzHugh‑Nagumo (7), Hindmarsh‑Rose (8), Morris‑Lecar (2), Spike Response Model (2), Izhikevich (10), and others using non‑CMOS materials such as RRAMs, memristors, biristors, and photonic components (6).

🔍 In Layman's Terms

Before building anything new, the authors did a literature census: of 100 hardware neuron papers from the last two decades, more than half used the two oldest, simplest models (IAF/LIF). More biologically realistic neuron models were usually implemented as analog circuits rather than efficient digital hardware, because translating their differential equations into digital logic is much harder.

TABLE 1
Hardware classification for 100 publications from 2000 to 2022.
Model Analog CMOS Emulation Others
IAF [1]–[9]
(32%)
[10]–[23]
(54%)
[24]–[27]
(14%)
LIF [28]–[41]
(38%)
[42]–[60]
(51%)
[61]–[64]
(11%)
FitzHugh–Nagumo [65]–[69]
(71%)
[70]
(29%)
None
(0%)
Hindmarsh–Rose [72]–[76]
(62%)
[77]–[79]
(38%)
None
(0%)
Morris–Lecar [80]
(50%)
None
(0%)
[81]
(50%)
SRM None
(0%)
[82]–[83]
(100%)
None
(0%)
Izhikevich [84]–[85]
(20%)
[86]–[93]
(80%)
None
(0%)
Others [97]–[98]
(33%)
[94], [95], [99]
(50%)
[96]
(17%)
Figure 1,2
Figure 1 & 2. Chart depicting the percentage of popular models that were turned into integrated circuits as well the percentage of hardware types

This survey showed that digital implementation is the most common way to deploy spiking‑neuron hardware, even though many researchers argue analog circuits are more power‑ and area‑efficient for neuron cells. The catch is that analog neuron hardware is vulnerable to device mismatch, leakage power, technology scaling limits, noise, and Process‑Voltage‑Temperature (PVT) variation — and it typically takes longer to design than digital circuits.

Because IAF and LIF are so simple, they miss dynamic properties real neurons have — like subthreshold oscillation and selective communication — so spiking networks built from them can't exploit those biological advantages. In 2001, Izhikevich proposed the resonate‑and‑fire (RAF) model, adding three dynamic properties to the IAF/LIF baseline while remaining, in his words, "an analogue" of the IAF model — powerful like Hodgkin‑Huxley, simple like IAF/LIF.

Yet from 2001 to 2022, only three integrated‑circuit realizations of RAF existed, and two of those were analog. Recent work has instead focused on FPGA emulations of the related Izhikevich model, typically using clock‑driven algorithms: shifters, the Euler method, or the CORDIC algorithm to avoid multiplication, and fixed‑point numbers to avoid floating point. Dedicated finite‑state machines were sometimes added to control model operation — all of which costs hardware resources and, because of the clock‑driven approach, dynamic power.

From the paper's motivation, the original RAF model was more hardware friendly than the Izhikevich model and other conductance‑based models — simple like IAF/LIF, but still carrying the important dynamic features of an analog neuron.

Contributions

🔍 In plain English

Imagine pushing a child on a swing. One push starts an oscillation. If the next push arrives at the right moment, it reinforces the motion; if it arrives too late, almost nothing happens. The proposed hardware recreates this timing-dependent behavior using digital logic instead of continuously solving differential equations.

What's Next

Having established why existing neuron models are difficult to implement efficiently in digital hardware, the next section introduces the original Resonate-and-Fire model and examines why previous hardware implementations remained limited.

Section II

The RAF Model & Related Work

The Resonate-and-Fire (RAF) neuron, introduced by Izhikevich in 2001, extends the classical integrate-and-fire neuron with timing-sensitive resonance. Instead of responding only to the amount of input, it also responds to when that input arrives.

🔍 In plain English

Imagine pushing someone on a swing. One push starts the swing moving. If the second push arrives at the right moment, it adds to the motion. If it comes too early or too late, very little happens. The RAF neuron behaves similarly: the first input starts a damped oscillation, and whether the second input triggers a spike depends on its timing.

Figure 3
  • The first impulse excites the neuron.
  • The membrane begins a damped oscillation.
  • The oscillation gradually loses energy.
  • If another impulse arrives during a high phase, both signals add together.
  • The summed voltage crosses threshold and produces a spike.

The oscillatory activity of an RAF neuron over time is:

(1)$$z = x + iy, \qquad \dot{z} = (b + i\omega)z$$

where where z ∈ C denotes a complex-valued neuron state, with current part x and voltage part y. On the first impulse, membrane voltage begins a damped subthreshold oscillation with frequency ω and damping constant b, caused by membrane impedance.

This is the central challenge addressed by the paper: although Equation (1) accurately describes the neuron's dynamics, it provides no obvious path to a digital circuit implementation.

An earlier analog realization [97] used a Lotka–Volterra oscillator built from subthreshold MOSFETs to play the role of the damped oscillator. Although innovative, the circuit depended on thermal voltage and supply voltage, making it highly sensitive to process, voltage, and temperature (PVT) variation as well as transistor mismatch. A second design [98] integrated incoming signals during the oscillation's high state and reset during the low state. While similar in spirit, it ignored the actual timing between successive impulses, preventing it from reproducing the RAF model's selective communication property.

Design [97]

Lotka–Volterra Analog Oscillator

Implemented the damped oscillator using a subthreshold MOSFET realization of the Lotka–Volterra equations.

Main limitation
Highly sensitive to thermal voltage, supply voltage, transistor mismatch, and overall PVT variation.
Design [98]

High/Low-State Integration

Integrated signals during the oscillation's high state and reset during the low state to approximate resonate-and-fire behavior.

Main limitation
Could not measure the true interval between impulses, so it lacked the selective communication property of the original RAF neuron.
🔍 In plain English

Both circuits captured part of the RAF idea, but each lost something important. One relied on fragile analog device physics, while the other simplified the timing behavior so much that it could no longer recognize precisely timed input spikes.

The Izhikevich Neuron Model & Its Digital Hardware Realization

In 2003, Eugene Izhikevich proposed a universal neuron model that could reproduce a wide variety of biological firing behaviors using a remarkably compact system of only two ordinary differential equations.

$$ \begin{aligned} v' &= 0.04v^2 + 5v + 140 - u + I,\\ u' &= a(bv-u),\\ &\text{if }v \ge 30\text{ mV, then }v \leftarrow c,\;u \leftarrow u+d. \end{aligned} $$

Here, v represents the membrane potential while u models the membrane recovery process. Setting a = 0.1, b = 0.26, c = −60, and d = −1 produces the characteristic resonator behavior.

The model quickly became one of the most influential neuron models because it achieved an exceptional balance between simplicity and diverse neuronal firing behaviors. Unlike the original RAF equations, it eliminates complex-valued variables and describes neuron dynamics using only two state variables. Despite this compact formulation, it can still reproduce many different neuronal firing patterns — including resonator behavior — making it practical for both neuroscience simulations and digital hardware implementations.

🔍 In plain English

This model is famous because it does a lot with very little. Two variables, no complex math, but still enough structure to mimic many real neuron behaviors. That is why hardware people care about it.


To implement this model on digital hardware, a Japanese research group proposed the Rotate-and-Fire Digital Spiking Neuron (RDN) [99]. Instead of representing the neuron state with continuous variables, the design encodes it using rotating bit patterns stored in two circular shift registers.

Circular Shifter A Membrane Potential (v) Circular Shifter B Recovery Variable (u) Five-State FSM Reset & Reconfigurable Logic Adders · Subtractors · Counters · Comparators Combinational & sequential update logic
RDN control & datapath flow

Each circular shifter always contains a single logic '1' that continuously rotates through its cells, allowing the two registers to encode the membrane potential and recovery variable over time. A dedicated five-state finite-state machine (FSM) controls the shifting direction, while reset circuitry and configurable interconnections recreate the reset behavior of the Izhikevich equations.

The architecture is highly flexible and can reproduce 14 different neuron-like firing responses, making it a general-purpose implementation of the Izhikevich model rather than a circuit dedicated only to resonate-and-fire neurons.

2
state variables (v, u)
5
FSM control states
14
firing patterns reproduced

However, this flexibility comes at a hardware cost. The implementation requires numerous combinational and sequential components — including adders, subtractors, counters, comparators, circular shifters, and a dedicated FSM — to coordinate every update. Since the shift registers rotate continuously, bits change state on every internal clock cycle, causing four flip-flops to switch every cycle and increasing dynamic power consumption. This behavior contrasts with biological neurons and simpler IAF, LIF, and RAF models, whose resting states consume almost no dynamic switching power.

Even when the neuron is completely idle, the shift registers continue rotating. The hardware therefore consumes dynamic switching power even when no spikes are being generated.
🔍 In plain English

RDN is flexible, but it burns more hardware to do it. The registers keep moving all the time, so the circuit is always switching instead of staying quiet at rest.

Trade-off: RDN trades power efficiency for flexibility — continuous bit rotation keeps the circuit "always active," unlike biologically event-driven spiking behavior.
Section III

A Digital RAF Model in the Complex Domain

A. Model

The membrane potential of the original RAF model is a damped subthreshold oscillation. In continuous-time mathematical models, this type of oscillation is typically represented by a damped sine wave. While this description is well suited for analysis, it is not convenient for implementation using purely digital hardware.

Instead of generating an analog sine wave, the authors model the subthreshold oscillation as a damped pulse train. A pulse train naturally matches digital logic because it consists of discrete high and low states rather than continuously varying voltages. To obtain an analytical expression for this digital waveform, the pulse train is expanded using a Fourier series, giving the following expression for the membrane potential:

(3)$$y(t)=v(t)=e^{-b(t-t_n)}\left\{Ad+\frac{2A}{\pi}\sum_{j=1}^{m}\frac{\sin(jπd)}{j}\cos\!\left[j\omega(t-t_n)\right]\right\}$$
(4)$$h_j=\frac{\sin(j\pi d)}{j},\qquad j\in[1,m],\quad m\ge1,\quad m\in\mathbb{N}$$

Here, the exponential term models the gradual decay of the oscillation, while the Fourier series reconstructs the damped pulse train from a sum of harmonic cosine components. This provides a mathematical description that remains suitable for analysis while closely matching the behavior of a digital implementation.

Here A is the membrane‑potential amplitude (in biology, roughly −65 mV to +30 mV; in digital hardware, a logic level such as +5 V, +3.3 V, or +1.8 V), d is the duty cycle, ω the subthreshold frequency, b the damping constant (<1), m the number of pulses, and tn the moment of the last impulse.

If ω = 0 and t ≫ tn, then y(t) = 0 — a resting potential of zero, unlike a real neuron's negative resting voltage. To give the model a constant negative resting level with no extra parameters, the authors add an offset of −A/2:

(5)$$y(t)=v(t)=e^{-b(t-t_n)}\left\{Ad+\frac{2A}{\pi}\sum_{j=1}^{m}h_j\cos\!\left[j\omega(t-t_n)\right]\right\}-\frac{A}{2}$$

The membrane current follows the conductance‑model relation I(t)=CV̇:

(6)$$I(t)=C\dot{V}$$
Go deeper — deriving the current part x(t)

Differentiating (5) with respect to time gives the current part of the neuron's state:

(7) $$ \begin{aligned} x(t)=I(t) &= C\frac{dv}{dt}=C\frac{dy}{dt}\\ &=Ce^{-b(t-t_n)}\Biggl[-b\Bigl\{Ad+\frac{2A}{\pi}\sum_{j=1}^{m}h_j\cos\!\bigl(j\omega(t-t_n)\bigr)\Bigr\}\\ &\qquad-\frac{2A}{\pi}\sum_{j=1}^{m}j\,h_j\sin\!\bigl(j\omega(t-t_n)\bigr)\Biggr] \end{aligned} $$

Based on [100] and [108], we assume that if there is any injected current while the membrane potential is oscillating, the state of the neuron is described by the following equation:

(8)$$\dot{z}=(b+i\omega)z+J_{\text{injected}}$$
Go deeper — solving for total membrane potential z(t)
(9) $$z(t)=\int\left[(b+i\omega)z+J_{\text{injected}}\right]dt=\int(b+i\omega)z\,dt+\int J_{\text{injected}}\,dt=x(t)+iy(t)+\int J_{\text{injected}}\,dt$$

Since the neuron's state is represented as a complex quantity containing both a current component and a voltage component, the integral of the injected current must also contain both parts. Otherwise, the voltage component of the neuron's state would remain unaffected by the injected current. The authors therefore assume that the injected current can be written as:

(10)$$\int J_{\text{injected}}\,dt=I_{\text{injected}}+iV(t-t_n)$$

where I_injected is a constant DC injected current and V(t−t_n) is the voltage integrated into the neuron's body at moment tn. So:

(11)$$z(t)=x(t)+I_{\text{injected}}+i\left[y(t)+V(t-t_n)\right]$$

Equation (11) suggests that the neuron's behavior can be interpreted as two parallel operations: a damped subthreshold oscillation of membrane potential (integration from Na+ channels) and an integration of current impulses (from Na⁺ channels). Their sum is the action potential. This structure gives the block model in Figure 4 of the source paper: a damped oscillator plays the role of the dendrite membrane, an integrator plays the role of the neuron's body, and a summing block — the axon hillock — combines them into the action potential.

Figure 4 All-digital RAF neuron block model, animated z(t) I_injected Damped oscillator Integrator L1 Σ Im(z) L2 Action potential
A block model of the Resonate and Fire Neuron Model.

Solving the integrator's potential by superposition (assuming ω = 0, t ≫ tn) gives capacitor‑discharge behavior:

(12)$$z(t)\big|_{\omega=0}=I_{\text{injected}}+i\left[-\frac{A}{2}+V(t-t_n)\right]$$
(13)$$V(t-t_n)=V_C(t)=V_n e^{-b(t-t_n)}$$

where VC(t) is the integrator's potential and b doubles as the neuron's time constant (membrane impedance). The charged potential at tn is:

(14)$$V_n=y(t)\big|_{t_n}+V_C(t)\big|_{t_n}+V_{\text{injected}}=y(t)\big|_{t_n}+V_C(t)\big|_{t_n}+b\tau I_{\text{injected}}$$

giving the neuron's action potential:

(15)$$V_A(t)=\operatorname{Im}(z(t))=y(t)+V_n e^{-b(t-t_n)}$$

VA therefore mixes subthreshold oscillation with spikes. In biology, dynamic polarization strips the subthreshold part out along the axon, so the action potential leaving the neuron becomes an all‑or‑none spike — effectively a digital pulse.

A resonator (unlike a pure integrator) doesn't naturally have all‑or‑none spikes — that depends on eigenfrequency, with a zero eigenfrequency reducing RAF to an integrator. Since subthreshold oscillation isn't useful for digital communication, the authors force all‑or‑none spikes in both cases by passing the total potential through a logistic function:

(16)$$V_{DA}(t)=\frac{1}{1+e^{-k\left[V_A(t)-V_{TH}\right]}},\qquad k\in\mathbb{R}$$

Small k (e.g. 1 or 2) preserves subthreshold ripple in VDA; very large k makes it a true digital pulse. VTH is set above the sum of the oscillation's peak and part of the integrator's contribution:

(17)$$V_{TH}=2y(0)=A\left(2d-1+\frac{4}{\pi}\sum_{j=1}^{m}h_j\right)$$

Putting (5), (7), (11), (13), (14), (16) and (17) together gives the full digital RAF (DRAF) equation system:

(18) $$ \left\{ \begin{aligned} h_j &= \frac{1}{j}\sin(j\pi d),\quad j\in[1,m],\ m\ge1,\ m\in\mathbb{N}\\[.4em] V_{TH} &= A\left(2d-1+\frac{4}{\pi}\sum_{j=1}^{m}h_j\right)\\[.4em] y(t) &= e^{-b(t-t_n)}\left\{Ad+\frac{2A}{\pi}\sum_{j=1}^{m}h_j\cos\!\left[j\omega(t-t_n)\right]\right\}-\frac{A}{2}\\[.4em] x(t) &= Ce^{-b(t-t_n)}\Biggl\{-b\Bigl[Ad+\frac{2A}{\pi}\sum_{j=1}^{m}h_j\cos\!\bigl(j\omega(t-t_n)\bigr)\Bigr]-\frac{2A}{\pi}\sum_{j=1}^{m}j h_j\sin\!\bigl(j\omega(t-t_n)\bigr)\Biggr\}\\[.4em] V_n &= y(t)\big|_{t_n}+V_C(t)\big|_{t_n}+b\tau I_{\text{injected}}\\[.4em] z(t) &= x(t)+I_{\text{injected}}+i\left[y(t)+V_n e^{-b(t-t_n)}\right]\\[.4em] V_{DA}(t) &= \frac{1}{1+e^{-k\left(\operatorname{Im}(z(t))-V_{TH}\right)}} \end{aligned} \right. $$

Fixed parameters: A, m, b, k — depend on hardware characteristics (voltage level, how fast the neuron returns to rest). Configurable parameters: d, ω — duty cycle and subthreshold frequency, which act like a perceptron's weights, tuned to data and application.

Figure 5 Figure 5
Figure 5. Proposed block model of the digital RAF neuron model.
💡 One way to think about it (Analogy)

The following is an analogy to build intuition—it is not part of the paper's mathematical formulation.

Imagine striking a bell. One parameter controls how long the ringing lasts, while another controls the ringing frequency. If a second strike arrives while the bell is still ringing strongly, the combined vibration exceeds a threshold and produces an output. The equations in this section formalize that intuition by representing the oscillation, defining the threshold, and converting the result into a digital spike.

B. Simulation (R language)

Fixed parameters: A = 1, m = 3, b = 0.02, k = 5000. Configurable parameters: d = 0.3 (30%), ω ≈ 125.7 rad/s (20 Hz). Simulation length 300 ms, resolution τ = dt = 0.1 ms, threshold V_TH ≈ 1.37.

1) Evoking damped oscillation — single impulse at tn = 110 ms

A single impulse (0.2 amplitude, 0.1 ms duration) pushes the membrane potential up but stays below the 1.37 threshold, then evokes the damped oscillation.

Figure 6
Figure 6. States of the DRAF neuron in a complex domain with one injected current pulse at tn = 110ms and dt = 0.1ms.
Figure 7
Figure 7. Potentials of the DRAF neuron's components over time with one injected current pulse at tn = 110 ms and dt = 0.1 ms.

Resting level is −0.5. With b = 0.02 and an eigenperiod of 50 ms, the damped wave shows two significant pulses at 110 ms and 160 ms, the second peak being half the height of the first. The integrator's Vc curve samples the membrane potential at injection and leaks toward zero. In Fig. 6, a white region marks all trajectories that simply decay back to rest, while a gray region marks trajectories whose next crossing could trigger a new oscillation.

Figure 1
Figure 8, 9, 10, 11.

2) Resonating event — second impulse exactly one eigenperiod later

With the second impulse arriving 50 ms after the first (matching the 50 ms eigenperiod), the trajectory is pulled from a still‑elevated state into the gray region again, this time crossing V_TH = 1.37 and firing — the neuron resonates and fires.

3) Non‑resonating case — interval = half the eigenperiod

With a shorter, mismatched interval, the trajectory is close to resting when the later impulses arrive, and never rises high enough to fire — only subthreshold ripple appears. This confirms the model's frequency preference, also called selective communication.

Six panels: membrane potential and single action spike for the resonant two-pulse case; complex-plane trajectories; and three traces for the non-resonating three-pulse case showing no firing.
Figures 12–13. Membrane potential and resulting spike for two resonant pulses (110, 160 ms). Figure 15. Complex-plane trajectory, three pulses (110, 130, 160 ms). Figures 16–17. Membrane potential and action potential for the same three pulses — subthreshold ripple only, no spike, since the 130→160 ms interval is half the eigenperiod.

4) Coincidence event — two impulses only 5 ms apart

With duty cycle d = 0.3 (a 15 ms high‑state window) and only a 5 ms gap between two impulses, the integrator hasn't leaked much energy and rises quickly to a high level. The trajectory is already outside the "safe" white region when the second impulse lands, so it easily crosses V_TH and fires — demonstrating coincidence detection, the same property found in the original RAF model.

Section IV

The All‑Digital Model

The simulations presented in Section III confirm that the proposed Digital Resonate-and-Fire (DRAF) neuron successfully reproduces the three defining dynamic properties of the original RAF model: damped subthreshold oscillation, selective communication, and coincidence detection. Although the DRAF model already produces all-or-none output spikes, the damped oscillator within the neuron still generates an analog oscillatory waveform (as shown in Figure 7). To achieve a fully digital implementation, the authors introduce an additional logistic function (L1) immediately after the oscillator. This stage converts the analog damped oscillation into a train of discrete digital pulses while preserving the neuron's resonant behavior, resulting in the proposed all-digital RAF model.

🔍 In plain English

Up to this point, the damped oscillator still produces an analog-like subthreshold waveform. To obtain a fully digital implementation, the authors introduce an additional logistic function after the oscillator, converting this waveform into a true digital pulse train. The resulting pulse train preserves the timing and damping behavior of the original oscillation while allowing the neuron to be implemented using standard digital logic.

The resonance detector operates as a small sequence detector whose logic states are summarized in Table 2.

Table 2 — Action mechanism of resonance detection in the all-digital RAF neuron circuit
Step Sub Clock Impulse Q0 Q1 Q2 RS_action
Reset 1 X 0 0 0 0
1 1 ↑ 1 0 0 0
2 0 X 0 1 0 0
3 1 ↑ 1 1 0 0
4 0 X 0 1 1 1
5 1 0 0 1 0 0

The subthreshold clock idles high at reset. The first impulse (Step 1) evokes the NCO; the second impulse (Step 3) samples its second pulse. During the transition from Step 3 to Step 4, the falling edge of the subthreshold clock shifts the sampled pulse into both Q1 and Q2. Their simultaneous high state asserts RS_action, after which Q2 is immediately cleared so that the detector is ready for the next resonance event, so RS_action pulses high and Q2 resets — an all-or-none spike is added to the action potential.

Using the same parameters as Section III‑B1 (damping b = 0.02, producing two effective pulses), the authors chose the half‑peak of the second pulse of the damped wave as L1's threshold and simulated the full timeline in R:

Figure 22 All-digital RAF neuron simulation trace, animated 100 200 300 400 500 600 700 800 900 1000 millisecond Vc Im(subOsc) Vth Im(cell_State) Action Impulse Long doublet (310→400ms, 90ms interval) — no spike Resonance: 500→550ms = eigenperiod (50ms) — SPIKE 650→670ms doublet drops into low phase — no spike Coincidence: 800/805ms within 15ms duty cycle — SPIKE
Figure 22. Simulation results of the all-digital RAF neuron using R language. First injection at t = 110 ms evokes two digital pulses (50 ms eigenperiod, 15 ms duty cycle). A long doublet (310–400 ms, 90 ms interval) fails to spike. A doublet at 500/550 ms has the same interval exactly and resonates, firing at 550 ms. A doublet at 650/670 ms (20 ms interval) falls into the oscillation's low phase and produces no spike. A coincident pair at 800/805 ms (5 ms interval, within the 15 ms duty cycle) triggers the coincidence detector and fires again.

Notice that only the damped oscillator is converted into a digital pulse train. The integrator intentionally remains waveform-based at the model level because its role is memory storage, and digital integrators are already straightforward to implement in hardware. This is also one reason IAF and LIF models have been widely adopted in neuromorphic circuits.

🔍 In plain English

Only the "ringing" part of the neuron is converted into digital pulses. The memory part is already naturally suited to digital circuits, so there is no need to redesign it. This keeps the architecture simpler while preserving the neuron's original behavior.

Figure 22 illustrates four representative stimulus cases.

  • t = 110 ms — first injection evokes two digital pulses (50 ms eigenperiod, 15 ms duty cycle) on Im(subOsc), then the oscillator falls silent from 200–300 ms — analog damped wave has been converted into a digital pulse train.
  • 310–400 ms — a doublet whose interval exceeds the eigenperiod: no spike on Action.
  • 500–550 ms — a second doublet, spaced at the 50 ms eigenperiod: Im(cell_State) crosses Vth, producing an all-or-none spike at 550 ms.
  • 650–670 ms — a 20 ms doublet, shorter than the eigenperiod but the second impulse falls into the oscillation's low phase (15 ms duty cycle): no spike between 650–800 ms.
  • 800/805 ms — a 5 ms coincident doublet, well within the 15 ms duty window: easily pulls membrane potential above threshold.

These results demonstrate that a true digital pulse train can faithfully reproduce the RAF model's dynamic behaviors while remaining compatible with digital hardware. Consequently, the proposed digital and all-digital RAF models provide practical alternatives to traditional IAF and LIF neurons for hardware implementation.

Section V

Hardware Implementation

A. Digital Circuit Design

In the proposed all-digital block model, the damped oscillator and the first logistic function (L1) are merged into a single hardware block implemented as either a Digitally Controlled Oscillator (DCO) or, equivalently, a Numerically Controlled Oscillator (NCO). By enabling or disabling the oscillator, this block generates the damped digital pulse train required to reproduce the neuron's resonant dynamics. Meanwhile, the integrator remains responsible for preserving the neuron's internal state by storing the membrane potential at the moment each input impulse is received.

Visually, the relationship between membrane potential and injected current (Fig. 3) mirrors an analog signal being captured by a sampling clock in analog‑to‑digital conversion. So the authors implement the integrator's job with a sample‑and‑hold circuit (Figure 24 in the source paper): a D flip‑flop clocked by the current impulses, with its data line fed by the oscillator (DCO/NCO). This captures the oscillation's phase at the moment of injection into a buffer that behaves like the integrator. Because only the two nearest impulses matter for detecting resonance and coincidence, 2‑bit shifters serve as phase accumulators.

🔍 In plain English

Instead of continuously calculating the neuron's state every clock cycle, the circuit simply samples the oscillator whenever an input spike arrives. Each sample records whether the oscillation was in a high or low state at that instant, allowing later logic to detect resonance using only flip-flops and logic gates.

The authors observe that the relationship between the injected current and the membrane potential closely resembles the operation of an analog-to-digital converter (ADC). Instead of continuously integrating the oscillatory waveform, the circuit only needs to capture the membrane state at the precise moment an input impulse arrives. Consequently, the oscillator output is sampled only at these discrete instants, preserving the neuron's state while greatly simplifying the hardware implementation.

Figure 24 Figure 24
Figure 24 shows the sample-and-hold circuit that replaces the mathematical integrator. The injected impulse acts as the sampling clock, while the oscillator output becomes the sampled data. The stored value therefore represents the neuron's state at the exact moment of stimulation.
Figure 25
Figure 25. General schematic of the proposed all-digital RAF neuron cell.
Figure 26 and 27
Figure 26. Circuit design of the 8-bit numerically controlled oscillator (NCO).
Figure 27. Delay circuit implementation used in the FPGA design.

Walking through Figure 25:

  • The n-bit NCO is programmed by Duty[n-1:0] and Weight[n-1:0] and driven by a high-speed clock (removable if the NCO is a ring oscillator). An impulse sets Osc Enable via DFF Q4, enables the NCO. from reset to generate the subthreshold oscillation.
  • A 3-bit shifter (Q5, Q6 counting pulses, Q7 flipping on the third pulse) forms the Oscillation Damper — it resets the NCO after three pulses, holding that reset until a new impulse arrives. Because of Q4, an impulse can't re-trigger an already-oscillating NCO; the NCO only leaves reset once the gap since the last enabling impulse exceeds three oscillation periods. This limits the oscillator to a finite number of pulses, reproducing the damped behavior predicted by the mathematical model.
  • Two sample-and-hold circuits, Q0 and Q8, catch the oscillation's phase on every injection — Q0 during the oscillation's high phase (excitatory injection), Q8 during the low phase (sampling inverted, high-level pulses). An injection landing here implies the last doublet's interval is between the duty cycle and the eigenperiod, so a reset clears the resonance detector's phase accumulator.
  • After the first oscillation pulse, sampled data shifts into Q1 (latest bit) then Q2 (oldest bit) on the oscillation's falling edges — the Resonance Detector. If both go high, the last two impulses were spaced about one eigenperiod apart; an AND gate raises RS_action, which is delayed briefly and fed back to clear Q2 (keeping Q1's latest bit alive for continuous firing under sustained resonance).
  • During the oscillation's high phase, the oscillator is effectively stopped and the neuron behaves like a plain IAF neuron — coincidence can't use the shifting clock, so a second buffer, Q9 after Q0, forms the Coincidence Detector, clocked directly by the injected pulse and accumulating '1's like a digital IAF neuron. An AND gate again derives the action from Q0 and Q9, with the result delayed and fed back to clear Q9.
  • The final action potential sums the resonance detector's and coincidence detector's outputs. Excitatory spikes are OR'd into a single spike train; inhibitory spikes pass through an XOR gate to cancel excitatory ones (two inverters reduce a race condition against the excitatory OR gate). Because XOR sums all impulses, inhibitory spikes can also evoke the NCO's pulse train — reproducing the RAF model's post-inhibitory spikes property.

The whole design uses only basic logic gates. No multipliers, adders, floating-point arithmetic, or real-number operators are required. The entire neuron is constructed from standard logic gates and D flip-flops. (NOT, AND, OR, XOR) and D flip-flops — a schematic that maps directly onto standard CMOS VLSI processes.

B. Implementation on FPGA

The NCO can be built from digital self-oscillators such as ring oscillators; on the FPGA (a clock-driven device) the authors instead use an 8-bit binary up-counter driven by a high-speed clock (Figure 26 in the source paper), reset to a high output level, with all internal flip-flops steady and switching frequency zero at rest — so, per the dynamic power relation

(19)$$P_{\text{dynamic}}=\alpha \times V \times f^2$$

dynamic power is zero while resting. Once "Reset" is released, the counter compares its value to Weight and Duty using XNOR/AND comparators to set the oscillator's period and duty cycle. A delay cell — trivial in CMOS as two series inverters, awkward on an FPGA — is realized with a dedicated circuit (Figure 27).

Synthesizing the neuron cell (Figure 28, RTL structure) on an Intel Cyclone V 5CSEBA6U23I7 with Quartus Prime Lite required 20 ALM units and 23 registers, These measurements were obtained after Quartus Prime Lite synthesis for an Intel Cyclone V FPGA. — the source data behind Table 3. That budget suggests roughly 2000 neuron cells fit on this FPGA; using ALMs alone, one neuron costs about 54 ALM units, or 0.13% of the device's total ALMs.

Table 4 — Resource utilization for one neuron cell on an FPGA, compared across publications
Resource [99] [87] [54] [92] [60] This work
Year 2011 2013 2021 2022 2022 2022
Model RDN IZK LIF IZK LIF DRAF
Target FPGA Xilinx SPARTAN-3 Xilinx Virtex-4 Xilinx Zynq UltraScale+ Xilinx Zynq-7000Q Xilinx Virtex-7 Altera Cyclone V
ALMs NA NA NA NA NA 20
LUTs NA 1598 455 218 196 NA
Flip-flops 5 970 85 530 297 23
Multipliers NA 1 NA NA NA 0
Counters 3 (13-bit & 2×4-bit) NA NA NA NA 1 (ALMs & DFFs based)
Comparator 10 NA NA NA NA 1 (ALMs based)
Adders 5 NA NA NA NA 0
Subtractors 1 NA NA NA NA 0
DSP blocks NA NA NA 6 NA 0
ROM 16×10-bit, 16×4-bit NA NA NA NA 0

Compared with previous implementations, the proposed neuron eliminates multipliers, adders, subtractors, DSP blocks, ROM, and large state machines. The reduction in hardware complexity follows directly from representing resonance with pulse timing instead of numerically solving differential equations.

Table 5 — Analog RAF neuron [97] vs. this work's all-digital RAF neuron
Metric [97] This work
Year 2006 2022
CMOS process AMI 0.35 μm Intel 28 nm LP
Supply voltage 1.5 V 1.1 V
Eigenperiod 50 μs 50 μs
Impulse width 300 ns 200 ns
Response time, resonance event NA 5 μs
Response time, coincidence event NA 0 μs

Click a column header to sort either table.

Because the proposed neuron is entirely digital, it is inherently free from process-voltage-temperature sensitivity that affected earlier analog RAF implementations.

From Mathematical Model to Hardware

Section V replaces each mathematical block introduced earlier with a digital hardware implementation while preserving the same computational behavior.

Mathematical Block (Section III) Hardware Realization (Section V)
Damped Oscillator → Digitally Controlled Oscillator (DCO)
Integrator → Sample-and-Hold Circuit
Resonance Detector → Q1–Q2 Shift Register
Coincidence Detector → Q0–Q9 Buffer Register
Logistic Function (L2) → Output Logic
Action Potential Generation → OR/XOR Output Stage
This mapping provides a direct correspondence between the mathematical DRAF neuron developed in Section III and the digital architecture implemented in Section V, illustrating how each computational component is translated into synthesizable FPGA hardware.
Section VI

Results

A. Simulation

The RTL was simulated in Verilog with a 5 MHz high-speed clock (f_iClk), NCO weight nW = 250, NCO duty nd = 100, and injected-impulse duration τ = 1/f_iClk = 200 ns. These settings give an eigenfrequency f_oClkSub = 20 kHz, eigenperiod T = 50 μs, and duty cycle d = 20 μs (Figure 29 in the source paper).

Figure 28
Figure 28. RTL structure of the all-digital RAF neuron on an FPGA.
Figure 29
Figure 29. Simulation results for the all-digital RAF neuron.

Figure 29(a) — Excitatory spikes only. The neuron first remains idle while the interval between successive excitatory spikes is long. During this resting period, the NCO enable signal (enOsc) stays high and the oscillator output (oClkSub) remains inactive, resulting in essentially zero dynamic switching activity. Long doublets and short but non-resonant doublets do not produce an output spike. Around 1 ms, however, a doublet separated by approximately 50 µs matches the neuron's oscillation period, producing a resonance event and an output spike (oAct). Near 2 ms, a much shorter doublet with an interval below 20 µs triggers the coincidence detector, generating a second output spike.

Figure 29(b) — Excitatory and inhibitory spikes. The same experiment is repeated while inhibitory inputs are introduced. When excitatory and inhibitory spikes arrive simultaneously before 1 ms, they cancel each other, preventing the oscillator from being activated and keeping the neuron in its resting state. After this cancellation period, the neuron responds normally to valid resonance and coincidence events, demonstrating both inhibitory suppression and the post-inhibitory behavior described by the proposed all-digital RAF neuron.

B. Experimental Measurement

The design was verified on a DE10-nano development kit (Cyclone V 5CSEBA6U23I7, Intel 28 nm CMOS, 1.1 V core supply, 3.3 V TTL I/O), captured with a high-speed multi-channel oscilloscope (Figures 30–31 in the source paper). The captured waveforms show the neuron's subthreshold oscillation, the output action potential, the total input spike train, and the sample-and-hold flip-flop's output (Q0 in Fig. 25) — confirming the coincidence detector, the resonance detector, and the damped oscillation at rest. Thanks to the resonance effect, the neuron's response time falls within one eigenperiod.

C. Comparison Results

Per Table 4, the proposed all-digital RAF neuron needs the fewest resources of the compared designs. The closest related work [99] requires counters, comparators, adders, and subtractors; designs using the Izhikevich model [87], [92] use more than twenty times this architecture's flip-flop count and additionally require multipliers and DSP blocks, which raise design cost, chip area, and power. By Table 4's figures, this translates to an estimated 70%–90% savings in energy and chip area.

The proposed neuron has just two configurable parameters — eigenperiod and duty cycle — implemented here as two 8-bit buses, so an SNN of 2000 ADRAF cells needs only about 4 KB to store all neuron configurations. Because the pulse train slows to a stop at rest, dynamic power drops to zero there — a property ODE-based models can't share, since they continuously recompute neuron state every system clock.

Per Table 5, compared with the analog RAF neuron of [97] (AMI 0.35 μm CMOS), this all-digital design (Intel 28 nm CMOS) is free from PVT variation and uses transistors about 12 times smaller

Section VII

Conclusion

The resonate-and-fire model combines the dynamic timing behavior of a biological neuron with the simplicity of an integrate-and-fire model, but it has remained uncommon in hardware. This work proposes digital and all-digital RAF block models, then realizes the all-digital version in Verilog on an Intel Cyclone V FPGA.

The results confirm that the design reproduces the RAF model's key properties: damped subthreshold oscillation, resonance detection, coincidence detection, and post-inhibitory spikes, while requiring only 23 D flip-flops and no multipliers or floating-point arithmetic. :contentReference[oaicite:0]{index=0}

The implementation uses the fewest hardware resources among the compared designs, showing that RAF-style timing behavior can be realized efficiently in digital hardware.